Keep children and bystanders away while operating a

14 | English 
1 619 P11 351 | (1.10.13)
Bosch Power Tools
Safety Warnings for Jigsaws

Hold power tool by insulated gripping surfaces, when 
performing an operation where the cutting accessory 
may contact hidden wiring. Cutting accessory contacting 
a “live” wire may make exposed metal parts of the power 
tool “live” and could give the operator an electric shock.

Keep hands away from the sawing range. Do not reach 
under the workpiece. Contact with the saw blade can 
lead to injuries.

Apply the machine to the workpiece only when 
switched on. Otherwise there is danger of kickback when 
the cutting tool jams in the workpiece.

Pay attention that the base plate 9 rests securely on 
the material while sawing. A jammed saw blade can 
break or lead to kickback.

When the cut is completed, switch off the machine and 
then pull the saw blade out of the cut only after it has 
come to a standstill. In this manner you can avoid kick-
back and can place down the machine securely.

Use only undamaged saw blades that are in perfect con-
dition. Bent or dull saw blades can break, negatively influ-
ence the cut, or lead to kickback.

Do not brake the saw blade to a stop by applying side 
pressure after switching off. The saw blade can be dam-
aged, break or cause kickback.

Use appropriate detectors to determine if utility lines 
are hidden in the work area or call the local utility compa-
ny for assistance. Contact with electric lines can lead to fire 
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage.

Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.

Always wait until the machine has come to a complete 
stop before placing it down. The tool insert can jam and 
lead to loss of control over the power tool.

Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e.g., against 
continuous intense sunlight, fire, water, and 
moisture. Danger of explosion.

In case of damage and improper use of the battery, 
vapours may be emitted. Ventilate the area and seek 
medical help in case of complaints. The vapours can irri-
tate the respiratory system.

Use the battery only in conjunction with your Bosch 
power tool. This measure alone protects the battery 
against dangerous overload.
Product Description and 
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire 
and/or serious injury.
While reading the operating instructions, unfold the graphics 
page for the machine and leave it open.
Intended Use
The machine is intended for making separating cuts and cut-
outs in wood, plastic, metal, ceramic plates and rubber while 
resting firmly on the workpiece. It is suitable for straight and 
curved cuts with mitre angles to 45°. The saw blade recom-
mendations are to be observed.
The light of this power tool is intended to illuminate the power 
tool’s direct area of working operation and is not suitable for 
household room illumination.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Battery pack
2 Battery unlocking button
3 “PowerLight” button
4 Thumbwheel for stroke rate preselection
5 Battery charge-control indicator
6 Temperature control/overload protection indicator
7 On/Off switch
8 Adjusting lever for orbital action
9 Base plate
10 Guide roller
11 Stroke rod
12 Plastic sliding shoe
13 Lead for the parallel guide
14 Saw blade*
15 “PowerLight”
16 Extraction hood
17 Handle (insulated gripping surface)
18 SDS clamping lever for saw blade release
19 Contact protector
20 Vacuum connection
21 Vacuum hose*
22 Splinter guard
23 Nose plastic sliding shoe
24 Screw
25 Scale for mitre angle
26 Locking screw for parallel guide*
27 Parallel guide with circle cutter*
28 Centring tip of the circle cutter*
29 Allen key
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories 
can be found in our accessories program.
OBJ_BUCH-1994-001.book  Page 14  Tuesday, October 1, 2013  2:18 PM

 English | 
15
Bosch Power Tools
1 619 P11 351 | (1.10.13)
Technical Data
Noise/Vibration Information
The vibration level given in this information sheet has been 
measured in accordance with a standardised test given in 
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different 
applications, with different accessories or insertion tools or is 
poorly maintained, the vibration emission may differ. This 
may significantly increase the exposure level over the total 
working period.
An estimation of the level of exposure to vibration should also 
take into account the times when the tool is switched off or 
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working 
period.
Identify additional safety measures to protect the operator 
from the effects of vibration such as: maintain the tool and the 
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with the fol-
lowing standards or standardisation documents: EN 60745 
according to the provisions of the directives 2009/125/EC 
(Regulation 1194/2012), 2011/65/EU, 2004/108/EC, 
2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division 
D-70745 Leinfelden-Echterdingen 
Leinfelden, 23.08.2013
Assembly

Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 
There is danger of injury when unintentionally actuating 
the On/Off switch.
Battery Charging

Use only the battery chargers listed on the accessories 
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full 
capacity of the battery, completely charge the battery in the 
battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure 
does not damage the battery.
The lithium ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.
Observe the notes for disposal.
Cordless Jigsaw
GST 10,8 V-LI
Article number
3 601 EA1 0..
Rated voltage
V=
10.8
Stroke rate at no load n
0
min
-1
1500 –2800
Stroke
mm
18
Cutting capacity, max.
– in wood
– in  aluminium
– in non-alloy steel
mm
mm
mm
70
3
3
Bevel cuts (left/right), max.
°
45
Weight according to 
EPTA-Procedure 01/2003
kg
1.5*
* dependent of the battery pack being used
Battery
Permitted ambient 
temperature
– when charging
– during operation*
– during  storage
°C
°C
°C
0...+45
–20...+50
–20...+60
Recommended batteries
GBA 10,8V x,xAh O–.
* Limited performance at temperatures <0 °C
GST 10,8 V-LI
Measured sound values determined accord-
ing to EN 60745.
Typically the A-weighted noise levels of the 
product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
dB(A)
dB(A)
dB
77
88
3
Vibration total values a
h
 (triax vector sum) 
and uncertainty K determined according to 
EN 60745:Cutting board:
a
h
K
Cutting sheet metal:
a
h
K
m/s
2
m/s
2
m/s
2
m/s
2
5.5
1.5
5.0
1.5
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-1994-001.book  Page 15  Tuesday, October 1, 2013  2:18 PM

16 | English 
1 619 P11 351 | (1.10.13)
Bosch Power Tools
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator 
5 
show the charging status of the battery 
1. The battery charge-
control indicator only illuminates for 5 seconds after start-up.
When no LED lights up after switching on, then the battery is 
defective and must be replaced.
Replacing/Inserting the Saw Blade

When mounting the saw blade, wear protective gloves. 
Danger of injury when touching the saw blade.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the 
end of these instructions. Use only T-shank saw blades. The saw 
blade should not be longer than required for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A)

Clean the shank of the saw blade before inserting it. An 
unclean shank cannot be fastened securely.
Insert the saw blade 
14 into the stroke rod 11 until it latches. 
The SDS lever 
18 automatically snaps to the rear and the saw 
blade is locked. Do not manually press the lever 
18 toward 
the rear, otherwise you could damage the machine.
While inserting the saw blade, pay attention that the back of the 
saw blade is positioned in the groove of the guide roller 
10.

Check the tight seating of the saw blade. A loose saw 
blade can fall out and lead to injuries.
Ejecting the Saw Blade (see figure B)

When ejecting the saw blade, hold the machine in such 
a manner that no persons or animals can be injured by 
the ejected saw blade.
Turn the SDS lever 
18 forward towards the contact protector 
19 to the stop. The saw blade is released and ejected.
Dust/Chip Extraction
 Dusts from materials such as lead-containing coatings, 
some wood types, minerals and metal can be harmful to 
one’s health. Touching or breathing-in the dusts can cause 
allergic reactions and/or lead to respiratory infections of 
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered 
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials 
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable 
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the 
materials to be worked.

Prevent dust accumulation at the workplace. Dusts can 
easily ignite.
Connecting the Dust Extraction (see figures C–E)
Insert the vacuum connection 
20 into the opening of base 
plate 
9.
Place a vacuum hose 
21 (accessory) onto the vacuum con-
nection 
20. Connect the vacuum hose 21 with a vacuum 
cleaner (accessory). An overview for the connection of vari-
ous vacuum cleaners can be found at the end of these instruc-
tions.
To enable optimum dust extraction, use the splinter guard 
22 
if possible.
The vacuum cleaner must be suitable for the material being 
worked.
When vacuuming dry dust that is especially detrimental to 
health or carcinogenic, use a special vacuum cleaner.
Place the extraction hood 
16 onto the contact protector 19.
Splinter Guard (see figure E)
The splinter guard 
22  can prevent fraying of the surface while 
sawing wood. The splinter guard can only be used with certain 
saw blade types and only at a cutting angle of 0°.
Insert the splinter guard 
22 into base plate 9 from the front.
The splinter guard 
22 can also be fitted with the mounted 
plastic sliding shoe 
12.
Sliding Shoe (see figure F)
When working with sensitive surfaces, use the plastic sliding 
shoe 
12.
To put on the plastic sliding shoe 
12, place the front edge of 
the base plate 
9 under the nose of the plastic sliding shoe 23. 
Then press the power tool onto the plastic sliding shoe 
12 un-
til it engages.
When using the plastic sliding shoe 
12, the splinter guard 22 
is inserted not into the base plate 
9, but rather the sliding 
shoe.
Operation
Operating Modes

Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 
There is danger of injury when unintentionally actuating 
the On/Off switch.
Orbital Action Settings
The adjustable orbital action allows for optimal adaptation of 
cutting speed, cutting capacity and cutting pattern to the ma-
terial being worked.
The orbital action can be adjusted with the adjusting lever 
8, 
even during operation.
LED
Capacity
Continuous lighting 3 x green
2/3
Continuous lighting 2 x green
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
Flashing light 3 x green
Empty
Orbital action switched off (level 0): No orbital action
Orbital action level I:
Small orbital action
Orbital action level II:
Large orbital action
OBJ_BUCH-1994-001.book  Page 16  Tuesday, October 1, 2013  2:18 PM

 English | 
17
Bosch Power Tools
1 619 P11 351 | (1.10.13)
The optimal orbital action setting for the respective applica-
tion can be determined through practical testing. The follow-
ing recommendations apply:
– Select a lower orbital action setting (or switch it off) for a 
finer and cleaner cutting edge.
– For thin materials such as sheet metal, switch the orbital 
action off.
– For hard materials such as steel, work with low orbital 
action.
– For soft materials and when sawing in the direction of the 
grain, work with maximum orbital action.
Adjusting the Cutting Angle (see figure J)
The base plate 
9 can be swivelled by 45° to the left or right for 
mitre cuts.
Remove the vacuum connection 
20.
In mitre angle 0° there is a pin in a corresponding recess.
Loosen the screw 
24 with the Allen key 29 until you can slide 
the base plate 
9 in toward the battery 1. Let the pin slide into 
the guide groove.
For adjustment of precise mitre angles, swivel the base plate 

жүктеу/скачать 9,24 Mb.

Достарыңызбен бөлісу: